"Install the new 3 holders on the unit. Retest the unit and unit passes all test at this time, check for gas leak with detector and no leaks found at this time. Job complete"

"Paradise Appliance ordered control- never returned. Ran diagnostics. Had f0e5, f0e7, f7e1 error codes. Cleared error codes. Found using ungrounded extension cord. Swapped out ext cord. Fills, agitates, drains, rinses, and spins properly at this time. Instructed customer to call electrician or move washer close to wall receptacle. Instructed customer on unbalanced loads, detergent usage. Complete."

"Removed and replaced compressor,vacuumed system and recharged up to 5.25 oz of r134 a. Unit started to cool, asked cx to monitor temp and report any issues."

CX says the fridge was not cooling a few days ago. Said the unit started working right before I showed up. Put unit into defrost checked the power thru the circuit. The power is good element is activating. The bi metal good power good. The unit is in the garage where temps go below 35*. This can cause cooling issues. CX INSTRUCT ABOUT AMBIENT TEMPS AND HOW IT AFFECT THE COOLING. AS THE TEMS GET WARMER THE UNIT WILL OPERATE AND CYCLE PROPERLY. Unit operating g properly.

"Replace the heater harness evaporator Thermistor and made sure the evaporator heater ohmed out good it did, reinstalled all the electrical on the evaporator fan motor and connected everything and put the cover back on tested operations unit is working as designed the last 24 hours for the unit to cook correctly"

Replaced water valve. Home water pressure to high and causing loud sound when using water dispenser and when the ice maker calls for water. Cx needs a plumber.

Installed parts tested check out ok complete no dents or dings cause by tech.

replaced parts per tech line tested unit all functions working properly job complete

I replaced the fill valve assembly and when it comes time for the valve to stop the flow of water now stops. All other functions tested properly. No error codes in diagnostics. . Job completed.

Starts then stopsConfirmed.water valve not mixing water properlythermistor harness disconnected..reinstalled and reset control. Designed operation was restored.

Removed and replaced magnetron and diode. Tets3d unit. All ops checked good

"Fixed- installed new parts (cntrl elec, latch, valve) calibration test pass- auto test pass- no errors- no leaks- cx ok repair."

Found unit with a weak igniter. Causing unit to leak and smell like gas. Needs igniter.Custimer approves. I stalled igniter. Tested unit. Unit is working properly.

Found loose connection to flow switch fix connection tested unit and is working properly

Changed opponents and unit is working as intended.

Customer concerns. Microwave not powering on. Installed new fuse. Operation tested as designed.

Drain pump had rock stuck in impeller removed rock drain is working properly and unit is washing per design job complete

"Upon arrival found unit no producing any ice, check the unit and found the ice maker off, switch the ice maker to on position. Recycle the ice maker and everything is working properly. Job complete"

Found lights off and sometimes flickering. Had 2 replaced. Tighten freezers doors handle and adjusted door for a good closing. All lights came back

"I installed all new LED lights inside both refrigerator and freezer side, unit is working as designed."

NoiseyConfirmed fan noise in freezeradjusted.normal operation

Install the new ice maker on the unit. Cycle the ice maker and unit passes all test at this time. Job complete Inform the customer they need wait at least 24hrs in order to see ice production.

Removed and replaced console. Tested unit. All tests good.

Installed handle. Tested. Unit is working properly. Customer approves.

Installed new start switch and tested unit working as designed

Replaced dispenser drawer Unit working properly as designed

Found after replacing the module that restored the lights inside the refrigerator. All other functions tested properly. Job completed.

JB Out 12/23/22. Installed replacement User Interface as ordered. Tested operation with customer. Unit now operates as designed. No charge to customer. JOB COMPLETE

After replacing the freezer door all functions tested ok. The new hose for the water dispenser had a different connector end so had to use a different connector. All tested ok. Job completed. ; used 2 8201815 (Connector) from stock

Installed console. Tested. Unit is working properly. Customer approves function at this time.

"Found the freezer vents blocked a bit instructed con proper load. Found items against the basal, of the fresh food section. Instructed customer on not placing items against the back wall. Instructed customer on how the defrost cycle works with there r600a refrigerator. Defrost will cycle longer than previous refrigerators do to using a low wattage heater. During this time the freezer temps may rise higher than the customer is used to. Unit operating as designed."

F7/E4 F7/E9 F7/E3 F7/E8 Tilted the unit back and found the rotor was not installed(photo). Installed slider. Cleared error codes ran the diagnostic cycle. The unit is operating properly. All ops and functions normal.

"CX says the lower I e maker is not producing ice. Also the units display on inner door is coming off. Removed film from around the console, installed. Holding properly. The ice maker has good power, cycled the ice maker cycled and filled. The units issues are all set."

Installed new console. Unit now operating as designed. Complete.

Smell of gasConfirmed. 3 call countGas valve leaking consumer not keeping machine will return to Harlows kc

Replaced agitator tested good

Fixed- found unit not to be leveled- I then leveled feet unit is now leveled properly- cx ok repair-

Tested found drian pump unplugged reinstalled tested working to spec

Inspected unit and found removable agitator was clogged with algae. Removed and ran clean cycle. Advised Cx to rinse and use afresh tabs. Unit passed all test working per design. Job complete

Installed new parts. Operation tested as designed. No leaks.

Replaced capacitor and control all tested good

Removed and replaced controls. Tested. Now working properly. Job complete

Installed new pressure hose and pressure switch. Unit has passed all test. Spins great and water is good. Job complete

"Recall 10/29/22, 11/16/22. Replaced FC drawer slides. Unit is cooling properly at this time. FC drain is clear at this time. Instructed lights will reset( lights shut down after doors are open for a long time ). Complete."

Installed new fascia assembly and tested unit working as designed

"Found ice maker arm broken. Installed new ice maker, ran harvest test. Operation tested as designed. No leaks. I was unable to document, techline closed."

"Found broken wire on drain pump, fixed broken wire and tested unit working as designed"

"Installed and secured new parts listed, tested unit, unit is now operating properly as designed at this time of service, customer approved repairs"

Replaced all selected parts Unit working properly as designed

Replaced parts tested unit all functions working properly Job complete

Installed motor and control. Loaded unit with towels and let the unit wash and spin out for the rinse. Unit operating as designed.

"The unit was completely off, only the interior lights were working. Checked the electrical outlet, it checked fine, connections and voltage at the main board checked fine. Found the user interface wire harness was not connected at all at the bottom of the freezer door. Connected the harness, the unit powered on right away, and started working as designed."

Replaced components and tested. Unit now working as intended.

Raised left fresh food door to allow mullion to close properly.Tested ok

Found an open cold water valve had valve replaced; used 1 WPW10156253 (Valve) from stock

Installed wash pump no leaks working to spec

JB out 12/23/22. Customer states washing machine has displayed F3E1 several time since last . Customer informed me since my last service visit she has experienced at least one washload where it appeared that the water did not fill in the wash tub 2 times. Verified customer is no longer using HE turbo detergent which is two highly concentrated for this low fill high-efficiency washing machine. Customers is and has been using HE only detergent and measuring 1 teaspoon maximum as advised. Tested wash cycle with no clothing and verified a very small amount of soap service residual. Customer is also using clean washer cycle with clean water tablet. Ram diagnostics in extracted only one error code F3E1 Indicating the ACU Detects and out of range pressure signal. ran quick diagnostic tests and verified all components passed. unable to verify any mechanical deficiencies at this point. Tested washer in towels cycle with towels and no detergent added. Inspected and verified no residual detergent soapsuds at this time. Allowed drain and spin cycle to run without interruption. Verified unit successfully drains all water and spins as designed. No repair is recommended at this time. Should this code continue in the future recommendation would be to replace the pressure switch which is part number WPW10448876. No repair man today as though defect found. No charge the customer. Job complete

"Removed power from fridge. Installed components. Assembled unit, restored power. All ops normal."

Installed UI. Control and harness. Tested unit. Unit is working properly. Customer approves function at this time.

"Upon arrival found the floor with marks of water. Check the unit and found the unit has a bad suspension, this is causing the unit touch the floor with the cover for the motor and pulley. This is causing the unit have a angle and the water coming fro the top and bottom drain hose, this because the unit was installed on the wrong position of the dryer, and has this hose stretch and every single time when spin the unit bounces to much causing the leak from this area. Additional with the bad suspension this is causing the failure. This unit will need new suspension. Customer dont know if they want to continue with the repair. Job complete"

Replaced all selected parts Unit working properly as designed

Replaced control board and calibrated the washer

"Found defective glide, fixed glide, tested unit and is working properly"

"Found the unit, not cooling, verify problem, compressor not running, replace compressor, drier and service valve, charge refrigerant 48g R600a check compressor condenser and evaporator fan motors running normal ; used 1 W10913906 ( Service valve) from stock"

"Replaced defective control board and ui, tested unit and is working properly"

Customer stated oven doesn't heat all the time. Geek squad came and ordered ignitor but never came back. Removed and replaced ignitor customer had Tested all works good at this time.

Tested dryer not igniting or gas turning on. Checked continuity and voltage as well as ohms gas valve not reading correctly and igniter either. Will need gas valve and igniter job completed.

Customer stated that the unit is not cooling found sealed system leak which caused deli drawer display to short. quoted customer for parts out of warranty. Customer declined. Collected service call. Needs deli display and deli drawer

"Customer concerns. Washer not starting wash cycles (faulty latch). INSTALLED NEW LATCH FROM JOB #489586. IT was a long drive, so I needed to complete the job. Operation tested as designed. No leaks.; used 1 W11394572 ( Latch) from stock"

"Forums loose connection to drain pump, fixed drain pump. Tested unit and is working properly"

"The nut holding the belt pulley, came off, causing the pulley to rub on the cover. Used blue Loctite and reapplied. Tested the unit and all OK."

"Found bad rollers and idler, replaced rollers and idler,tested unit working as designed"

"Replaced both rails for the lower oven drawer, the drawer was still not closing properly. Called the technical department, was advised to check and push back a terminal block cover to allow the drawer to slide all the way to the back. Re installed the drawer, checked ops, the drawer is closing and making a proper seal.SR 7735344162"

Customer stated that console dies. Removed and replaced console tested all works good at this time.

The suspension is bouncy. The belt is loose. Installed bolt and suspension. Calibration passed. ; used 1 W11239857 (Belt) from stock

Repaired damaged wire going to drain pump. Tested after repair all ok.

The left door assembly was replaced which fixed issue. Cx tested as well as I did everything was in place and working. Job completed.

"The Model serial number is unreadable and the tag has been removed from the unit. Called the office who told me that the customer is to call Lowes and have them get a new model,serial tag for the unit. Without a picture of this on the unit we can not work on the unit. The leak is not from the washer(see pics) and the washer needs a suspension."

Replaced the drain pump. Verified that no leaks are present and that drain pump is functioning normally. Unit is functioning as designed.

Found the unit having issues draining. The brown wire was pinched going to pump. Repaired wire. Tested unit. All ops checked good

Found evap fan not running removed evap cover found hitting foam reset tested working to spec

Replacing parts needed. Replaced burner and now unit lights right away. No popping sound and heats. Tested after putting all back together. Unit is working correctly. Job completed

I found dryer squeezing installed kit tested working to spec

Removed and replaced evaporator fan and LED. All ops checked good

Pull the wrapper off and replace the control board that was burnt. Unit tested OK

F7E5 F2E1 f3e2. Replaced slider and ran cycle. Unit passed all tests and is operating as designed.; used 1 W10734521 (Slider) from stock

Install new parts on unit. Re-tested it and unit passed all test. Job complete

Fixed- installed new part (cntrl elec) all temperature setting are now working- unit has begun cooling- cx ok repair

Found gasket warp reheated retest ok complete no dents or dings cause by tech.

Customer stated that the unit has no power. Found defective power cord. Removed and replaced power cord tested all works good at this time.

Install the new harness on the unit. Retest the unit and unit passes all test at this time. Job complete

Replaced parts and tested unit job complete

Replaced part and tested unit

JB out 12/23/22. Installed replacement motor and blower wheel. Reassembled and tested operation with customer. Unit now operates as designed. No charge to customer. JOB COMPLETE

"Replaced fresh food compartment door gasket, applied adhesive sealant to the doors gasket channel, and applied heat to the gasket to de wrinkle and shape properly. The gasket is staying in place, and making a good seal around the perimeter."

Installed the new control board. Fridge started normal

Install new part on unit. Re-tested it and unit passed all test with no errors. Job complete

"Replaced the soap/aid dispenser assembly, verified that new dispenser is not leaking, reset board. Unit is functioning as designed."

Customer stated not enough water. No error codes. Tested unit and calibrated unit. Unit is working as intended.

"Advised customer to move large items located at the very top shelf which block airflow, large items needs to be stored on the lower shelf also Found that the Customer is blocking airflow from reaching the temperature sensor with aftermarket containers, customer has issues with the no room for anything in the refrigerator compartment. I advised the customer that to move the container to a lower section to prevent from blocking the sensor. Customer showed me some noodles in a bowl fully exposed to the air that was located to the rear wall and stated that because of this they want another refrigerator. Freezer is functioning properly and icemaker is making ice. I advised the customer that the refrigerator is functioning as designed and that they would have to contact whirlpool customer service. Sr# 7735343009"