We serviced a
WHILPOOL DISHWASHER
Model WDF520PADM9
Near Simi Valley, CA 93065
Randy
Job Details: 03/10/2023
Removed and replaced pump n motor. Now working as designed. Job complete
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS325SDHZ01
Near Lancaster, CA 93536
Jonathan
Job Details: 03/10/2023
Found defective evaporator. Client will contact whirlpool for coverage on sealed system. WP2188823
We serviced a
WHIRLPOOL WASHER
Model MVW6230HW2
Near Los Angeles, CA 91335
Nick D
Job Details: 03/10/2023
"Already did notes on other ticket put///::.. After unit was grounded with 120 ac outlet came back today to replace main board with capacitor, once parts where replaced did test run tested all active components unit is now working properly everything has been fixed and ready to use, job completed."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX735SDHZ03
Near Los Angeles, CA 91331
Nick D
Job Details: 03/10/2023
"Unit was not dispensing any water at all all parts requested where replaced which fixed issue, with water no further problems job completed."
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near Patterson, CA 95363
William
Job Details: 03/10/2023
"Ziptied hoses to water lines, ran self diagnostic cycle, unit operating as designed."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT311FZDW02
Near Palmdale, CA 93551
Jonathan
Job Details: 03/10/2023
Found defective door seal. Fixed door seal tested unit and unit is working properly
We serviced a
KITCHENAID REFRIGERATOR
Model KRFF507HPS02
Near Visalia, CA 93291
J.E.
Job Details: 03/10/2023
Sr#7735920808. Cycled unit and found unit working as designed. Called Tech line to document. Call back please refer customer to Whirlpool customer service. Job completed
We serviced a
WHIRLPOOL WASHER
Model WTW5015LW0
Near Modesto, CA 95357
Bob S.
Job Details: 03/10/2023
Took out old unit installed new unit new unit worcking as designed Old unit wouldnt drain wouldnt stop going threw cycles
We serviced a
KITCHENAID DISHWASHER
Model KDTE204KPS1
Near Glendale, CA 91206
Juan
Job Details: 03/10/2023
"F10e4. Accessed the diverter motor harness connection, it was loose, corrected the connection. Cleared error code, ran diagnostics, the unit went through diagnostics cycle properly, did not prompt any error codes. Ran a normal cycle, the unit filled and started washing properly. The unit is not anchored down to the cabinet, it doesnt seem to slide back all the way. Pointed that out to the customer, and advised him to correct the installation. The unit is now working as designed."
We serviced a
KITCHEN AID REFRIGERATOR
Model KSSC48QVS10
Near Riverside, CA 92508
Nick D
Job Details: 03/10/2023
Replaced water valve in order to fix fill tube for Icemaker freezing over issue. Tested after repair all ok.
We serviced a
MAYTAG DRYER
Model MGDC465HW2
Near Glendale, CA 91202
Oscar L
Job Details: 03/10/2023
"Because of a none stopping creaking even when unit had stopped, a new timer assembly has been replaced."
We serviced a
WHIRLPOOL WASHER
Model MVW6230HW1
Near Ceres, CA 95307
Timothy G
Job Details: 03/10/2023
Installed all new parts recommend from techline. As soon as machine started the control again shorted out and now has now power. Calling techline again. Tech line admitted unit as unrepairable. Saftey issue. No repair. SR#7735866684 job complete
We serviced a
KITCHENAID DISHWASHER
Model KDFE204KWH1
Near Arroyo Grande, CA 93420
Brandon
Job Details: 03/10/2023
Installed new vent assembly. It came with a new gasket. Cx will let us know if problem persists.
We serviced a
KITCHENAID MICROWAVE
Model KMHS120KPS01
Near Moreno Valley, CA 92557
Kevin
Job Details: 03/10/2023
Removed and replaced bulb and main control. Tested unit. All tests good.
We serviced a
MAYTAG WASHER
Model MVW6230HW3
Near Los Angeles, CA 91342
Nick D
Job Details: 03/10/2023
"Strike was used was replaced because old one had one piece that was missing, once replaced no further issues, job completed."
We serviced a
MAYTAG WASHER
Model MVWC565FW3
Near San Dimas, CA 91773
Jaime
Job Details: 03/10/2023
"Installed the new outer tungsten, suspension, clutch. Washer ok. Pls. Get author. For double labor"
We serviced a
GENERAL ELECTRIC OVEN
Model PTD7000SN3SS
Near Nipomo, CA 93444
George
Job Details: 03/10/2023
Installed parts tested check out ok complete no dents or dings cause by tech.
We serviced a
WHIRLPOOL REFRIGERATOR
Model KRMF606ESS00
Near Riverside, CA 92504
Robert U.
Job Details: 03/10/2023
After replacing the freezer door and upper right bracket for the top shelf in the freezer all functions with the door tested ok. I recommended the unit still being unplugged for 24 hours to ensure the freezer evap is fully defrosted. Customer said she will leave it unplugged till tomorrow.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT318FZDW06
Near Pinon Hills, CA 92372
Cesar
Job Details: 03/10/2023
Replaced door tested good
We serviced a
MAYTAG WASHER
Model MVW7230HW0
Near Santa Clarita, CA 91387
Jonathan B.
Job Details: 03/10/2023
"JB out 3/10/23. Customer stated unit displayed Over temperature error.Ran diagnostics and verified F0E4 fault.Spin limited by water temperature. Ran a test 4, VALVES. Verified hot water when cold is called for. Installer reverser water supply hoses.Corrected water hose installation. Tested again. Water temperature is now correct. Cleared stored error code.no parts used. No charge to customer.JOB COMPLETE"
We serviced a
MAYTAG WASHER
Model MHW5630HW
Near Los Angeles, CA 91342
Nick D
Job Details: 03/10/2023
"The motor and stator where replaced as well as the main board because of error codes and obstruction to drum, after repair tested unit with all active components as well as in a drain and spin unit was spinning freely as well no further issues, job completed."
We serviced a
KITCHENAID COOKTOP
Model KFGC500JSS05
Near Rancho Cucamonga, CA 91730
Tyler
Job Details: 03/10/2023
Customer stated that the right and left front runners are taking too long to light and one of the burner heads has discolored. Removed and replaced burner heads and burner caps tested all works good at this time.
We serviced a
FRIGIDAIRE REFRIGERATOR
Model LGHB2869TF3
Near Bakersfield, CA 93312
Aaron
Job Details: 03/10/2023
"Replaced the freezer ice maker , tested ops ok now at this time"
We serviced a
MAYTAG DRYER
Model MGDC215EW0
Near Rancho Cucamonga, CA 91737
Tyler
Job Details: 03/10/2023
Customer stated that the unit stopped turning. Found broken belt. Removed and replaced rollers idler pulley and belt with dryer repair kit. Tested all works good at this time.; used 1 4392067 (DRYER REPAIR KIT) from stock
We serviced a
WHIRLPOOL DISHWASHER
Model WDT750SAKZ0
Near Montebello, CA 90640
Juan
Job Details: 03/10/2023
"Replaced the console and user interface board. Checked units ops, the unit is working as designed."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS571CIDM01
Near San Bernardino, CA 92404
Rod
Job Details: 03/10/2023
"Returned, replaced defective door as designed op will return in 24-48 hrs. Will"
We serviced a
MAYTAG DISHWASHER
Model MDB4949SKZ0
Near Victorville, CA 92392
Drew M.
Job Details: 03/10/2023
Ran diagnostics and found an F9E1 error code. SR#7735240441 techline suggested clearing out suds with cold water and running drain till suds are gone.
We serviced a
MAYTAG DRYER
Model MGDC465HW1
Near Moreno Valley, CA 92553
Kevin
Job Details: 03/10/2023
Unit making noise during cycle. I removed front panel and drum. I found that the drum bearing has came out of drum in one spot. I reinserted and installed drum properly. Tested unit. All tests good.
We serviced a
WHIRLPOOL M/W OTR
Model WML55011HS07
Near Santa Clarita, CA 91350
Raymond
Job Details: 03/10/2023
"SR 7735915658. Due to the fact that the unit stops blowing from the front with venting disconnected and on a work bench and only happens when the vent is installed, this is a venting concern as discussed before. Tech already attempted to rectify vents for customer service to take care of Cx, this is external."
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC704FPS03
Near Burbank, CA 91506
Erick
Job Details: 03/10/2023
"Cycled ice make and found heater inside door . Unit has Brookner white ant heater. Tube is frozen causing no ice production. Removed front panel and found slightly burnt contact on water switch. Cleared corrosion and unit is still making contact, dispenser is now working but may stop again in there future. Door would need to be replaced as an assembly with switch to correct all failures. Repair would not be economical to repair."
We serviced a
MAYTAG WASHER
Model MHW8630HW0
Near Los Angeles, CA 91605
Oscar L
Job Details: 03/10/2023
"A new control panel and a inlet valve have been replaced, washer was tested with consumer as witness and worked fine. Shell continue to monitor throughout the weekend and will reach out should further help is needed."
We serviced a
WHIRLPOOL WASHER
Model WTW4955HW3
Near Los Angeles, CA 91406
Nick D
Job Details: 03/10/2023
Belt from the bottom of washer had came off loose and had to put back and attached to motor pulley and cam once did that tested unit with service test this time no issues unit was now spinning and working up to specs.
We serviced a
WHIRLPOOL DRYER
Model WGD5620HW3
Near Lancaster, CA 93534
Jonathan B.
Job Details: 03/10/2023
"JB out 3/10/23. Install replacement, appliance, control unit and human machine. Interface reassembled and tested operation with customer. Unit now powers up and allows cycle selection and runs as design. Verified controls are excepting commands, unit runs and heat circuit supplies heat. No charge to customer. Job complete."
We serviced a
MAYTAG WASHER
Model MVWX655DW1
Near Perris, CA 92570
Nick D
Job Details: 03/10/2023
"Found the hub worn out will need to replace Gearcase,hub, and washplate. Customer declined estimate they will replace the washer."
We serviced a
WHIRLPOOL DRYER
Model MGD8630HC0
Near Hidden Hills, CA 91302
Gabriel G
Job Details: 03/10/2023
"Found an F3E3 code present, cleared the fault code. Performed the vent test, vent test indicated a restriction on the venting. Recommended to customer to have the vent cleaned by a professional air duct company. If problem continues, customer will advise.
We serviced a
MAYTAG WASHER
Model MVW6230HW2
Near Palmdale, CA 93550
Jonathan
Job Details: 03/10/2023
Replaced defective control board. Tested unit and is working properly
We serviced a
WHIRLPOOL MICROWAVE
Model CAE2745FQ1
Near Fontana, CA 92335
Tyler
Job Details: 03/10/2023
Customer stated that unit has a burning smell. Checked unit for error codes found long fill code. Ran u it through diagnostics and checked gear case belt and pulley all working to specs. Fixed drain hose to eliminate long fill tested all works good at this time.
We serviced a
MAYTAG WASHER
Model MVWX655DW
Near Porterville, CA 93257
J.E.
Job Details: 03/10/2023
Cycled unit and found that water valve connection causing you need to fill. Secure connection and re-tested unit all test pass. Job completed.
We serviced a
KITCHENAID REFRIGERATOR
Model KRMF706ESS01
Near Avila Beach, CA 93424
Brandon
Job Details: 03/10/2023
Installed new compressor and drier and recharged. Unit was cooling after service. Cx to wait 24 hours before restocking.
We serviced a
WHIRLPOOL OVEN
Model KODE500ESS00
Near Los Angeles, CA 91356
Gabriel G
Job Details: 03/10/2023
Customer had calibration set 30 above the set default calibration to the lower oven. Set calibration to the default setting 0 degrees. Ran lower oven and verified that the temperature matches the temperature on my meter. Set calibration to 10 degrees above the default (0 degrees) and verified that temperature is reading correctly now. Advised customer on the proper calibration setting for the oven. Unit is functioning as designed. Collected $135 service fee via check
We serviced a
WHIRLPOOL REFRIGERATOR
Model Kbsd618ess01
Near Los Angeles, CA 91307
Sean W
Job Details: 03/10/2023
Replaced door stop. Fridge no longer swinging out and is closing properly.
We serviced a
WHIRLPOOL RANGE
Model WEG515S0FS2
Near Los Angeles, CA 91606
Leon
Job Details: 03/10/2023
Called tech line with ErikDocumented as non repairable
We serviced a
MAYTAG WASHER
Model MVW6200KW2
Near Los Angeles, CA 91335
Nick D
Job Details: 03/10/2023
"Called wp again for troubleshooting I let them know that although it wasnt as bad as last time with the cam being completely destroyed it still caused some minor damage again because Cx called right away said they hard loud cracking sound when trying to agitate second time after repair, wp said will go under engineer review and will be replaced they read their disclaimer to me, file number is (7735663515) job completed."
We serviced a
MAYTAG WASHER
Model MVW6200KW0
Near Oakdale, CA 95361
Martin R
Job Details: 03/10/2023
Replaced parts tested parts unit is working properly Job complete
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX735SDBM00
Near Pasadena, CA 91104
Stephen
Job Details: 03/10/2023
Replaced ice maker kit w/ harness. Harvesting and filling properly at this time. Instructed customer to allow 3-4 days for ice. Complete.
We serviced a
WHIRLPOOL DISHWASHER
Model KUDM245EWH5
Near Los Angeles, CA 91604
Oscar L
Job Details: 03/10/2023
"As per consumer, the door seal has been recently replaced and DW only leak to another person but, never to her.I have tested DW on a 3 different cycles and forced to drain and worked fine every tine and no leaks were spotted."
We serviced a
WHIRLPOOL DRYER
Model WGD95HEDW1
Near Santa Clarita, CA 91351
Raymond
Job Details: 03/10/2023
"On arrival Cx states unit has loud noise. No issue drying. Found seized rollers. Quoted Cx for repair. Additional labor due to space requirements. Cx approved. Installed repair kit and tested, unit functions as designed."
We serviced a
WHIRLPOOL WASHER
Model WTW8127LW0
Near Hesperia, CA 92345
Ian Y
Job Details: 03/10/2023
"Removed defective unit. Installed new unit. Tested new unit, works as designed. Customer said unit had multiple issues."
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Riverside, CA 92506
Robert U.
Job Details: 03/10/2023
Found after replacing the parts listed the motor is now functioning and so is all the other components. I recalibrated the unit and all tested properly. Job completed.
We serviced a
MAYTAG WASHER
Model MVWC565FW2
Near Fresno, CA 93710
Irvin
Job Details: 03/10/2023
"CX says the unit is making noise. The splutch is the cause. Removed power from unit, Installed replacement splutch. Passed calibration. All ops normal. ; used 1 W10721967 (Splutch) from stock"
We serviced a
GENERAL ELECTRIC DISHWASHER
Model GDT630PYR3FS
Near Tollhouse, CA 93667
Doug S
Job Details: 03/10/2023
"Installed new inner door and tested,unit working as designed"
We serviced a
KITCHENAID REFRIGERATOR
Model KBSD608ESS01
Near Calabasas, CA 91302
Felipe S
Job Details: 03/10/2023
Install the new reducer on the unit. Retest the unit and now unit is working properly. Job complete
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF560SEHZ00
Near Los Angeles, CA 91324
Sean W
Job Details: 03/10/2023
Replaced thermistor. Fridge now cooling properly.
We serviced a
MAYTAG WASHER
Model MVWB765FW3
Near Palmdale, CA 93551
Jonathan
Job Details: 03/10/2023
"While replacing slide noticed oil leaking from gearcase. Informed client of issue, client refuses further service. Client payed for service call. no parts or labor. At this time"
We serviced a
WHIRLPOOL DRYER
Model WGD5050LW2
Near Moreno Valley, CA 92557
Kevin
Job Details: 03/10/2023
Unit making loud rattle sound. I found that the burner cover was loose and rattling. I tightened burner cover. Tested unit. All tests good
We serviced a
WHIRLPOOL WASHER
Model WTW4855HW1
Near Patterson, CA 95363
William
Job Details: 03/10/2023
"Found stripped hub, Replaced hub assy, ran calibration cycle, ran self diagnostic cycle. Unit operating as designed. ; used 1 W10528947 (Hub assy.) from stock"
We serviced a
THERMADOR REFRIGERATOR
Model T30IR905SP/09
Near Bakersfield, CA 93314
Aaron
Job Details: 03/10/2023
"The top drawer popper out a bracket that is there to ensure drawer doesnt pop out off the bracket , repaired the right side slider hinge asm , tested ok now at this time"
We serviced a
WHIRLPOOL DRYER
Model WGD92HEFW0
Near Los Angeles, CA 91604
Oscar L
Job Details: 03/10/2023
"So Going through the process of elimination one more time, I have started with thermal fuse and that was the immediate fix."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF989SDAM00
Near Arcadia, CA 91006
Juan
Job Details: 03/10/2023
"Replaced the drain tube extension, checked ops. The defrost water is draining properly now."
We serviced a
WHIRLPOOL WASHER
Model WTW5010LW0
Near Bakersfield, CA 93312
Aaron
Job Details: 03/10/2023
"Replaced the motor ,actuator,belt and cam asm , tested ops ok now at this time"
We serviced a
MAYTAG WASHER
Model MVWB865GW0
Near Bakersfield, CA 93306
Joe
Job Details: 03/10/2023
Replaced part and tested unit job complete
We serviced a
WHIRLPOOL OVEN
Model JJW2827LL00
Near Santa Clarita, CA 91321
Raymond
Job Details: 03/10/2023
"Installed console, tested, all error codes cleared, unit functions as designed."
We serviced a
WHIRLPOOL REFRIGERATOR
Model KRMF706EBS04
Near Patterson, CA 95363
William
Job Details: 03/10/2023
"Found condensation on return system lines, Insulated return sealed system line. Adjusted temp on unit."
We serviced a
KITCHENAID DISHWASHER
Model KDTM404KPS0
Near Santa Clarita, CA 91351
Jonathan B.
Job Details: 03/10/2023
"JB out 3/10/23. Remove dishwasher 1/4 of the way forward from the cabinet installation. Found left hand door spring disconnected from door hinge. Reconnected spring to hinge and tightened all mounting screws. Also tightened the screws on right hand hinge. read test of operation. Door opens and closes as designed. Reinstall dishwasher into cabinet installation. Tested operation with customer door open, closes and parks as designed. No parts used. No charge to customer. Job complete."
We serviced a
WHIRLPOOL RANGE - ELECTRIC
Model WFE320M0JS
Near Delhi, CA 95315
Cruz
Job Details: 03/10/2023
"Fixed- installed new parts (cntrl elec, 3 burner element) tested, all top burners are working as designed, cx ok repair"
We serviced a
WHIRLPOOL DRYER
Model WED8127LC1
Near Winton, CA 95388
Cruz
Job Details: 03/10/2023
"Fixed- found unit to be rattling due to not not leveled - I then adjusted all 4 feet, unit is now leveled, no rattling sound as well- cx ok repair"
We serviced a
WHIRLPOOL WASHER
Model WTW5105HW1
Near Modesto, CA 95355
Timothy G
Job Details: 03/10/2023
Cx arrived as I was calling. Installed new valve assembly and tested. Recalibrated and no errors. unit is working per design.
We serviced a
WHIRLPOOL RANGE
Model AER6303MMS0
Near Los Angeles, CA 91601
Oscar L
Job Details: 03/10/2023
A new clock/UI has been replaced and unit was tested to customers satisfaction.
We serviced a
MAYTAG WASHER
Model MVWB865GW1
Near Gustine, CA 95322
Jonathan
Job Details: 03/10/2023
Installed valve tested no leaks working properly
We serviced a
WHIRLPOOL WASHER
Model WTW5010LW0
Near Visalia, CA 93291
J.E.
Job Details: 03/10/2023
"Cycled unit and found all components test normal. Instructed customer on proper loading, use of detergent And cycle selection. Unit working as designed. Job completed"
We serviced a
WHIRLPOOL OVEN
Model WOS31ES0JS
Near Los Angeles, CA 91042
Erick
Job Details: 03/10/2023
Upon arrival found panel not responding and door locked . Removed panel and manually opened door. Found faulty thermal fuse causing no power . Replaced and unit power back on . Lock disengaged. Retested oven and oven failed. Removed and found open rear tod. Removed and replaced. Retested it and hint is now cycling and heating . Job com
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS571CIHW00
Near Modesto, CA 95355
Bob S.
Job Details: 03/10/2023
Took out old unit installed new unit tested new unit new unit worcking as designed Customer said shelfs would not fit in old unit
We serviced a
AMANA WASHER
Model NTW4516FW4
Near Bakersfield, CA 93309
Aaron
Job Details: 03/10/2023
Replaced the main board tested ops ok now at this time
We serviced a
WHIRLPOOL DRYER
Model WGD4950HW1
Near Santa Paula, CA 93060
Devon W.
Job Details: 03/10/2023
Drum was damaged causing paint chipped installed new drum Complete
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near Gustine, CA 95322
Jonathan
Job Details: 03/10/2023
Installed all parts listed tested working properly
We serviced a
WHIRLPOOL WASHER
Model WTW6120HW2
Near Upland, CA 91784
Jaime
Job Details: 03/10/2023
Found several broken wire at the cap and motor connection reworked wires per customers consent. Put unit together and left washer working ok
We serviced a
KITCHENAID DISHWASHER
Model KDFE104HPS1
Near Los Angeles, CA 91307
Sean W
Job Details: 03/10/2023
Found small piece of plastic in filter. Removed and Ran diagnostic. Dishwasher working as intended. Cx provided pop.
We serviced a
FRIGIDAIRE ELECTRIC RANGE
Model FCWM3027ABB
Near Victorville, CA 92394
Cesar
Job Details: 03/10/2023
"Found failed communication between UI and main control, when unit was assembled the wires between ui and control got pinched, repaired wires all tested good"
We serviced a
MAYTAG DRYER
Model MEDB765FW0
Near Turlock, CA 95382
Cruz
Job Details: 03/10/2023
"Fixed- installed new parts (element, inner door) unit is heating, door is not popping out during any cycles- cx ok repair"
We serviced a
WHIRLPOOL WASHER
Model WFW6620HC3
Near Santa Clarita, CA 91387
Raymond
Job Details: 03/10/2023
"Cx states unit moves during spin, unit on slippery flooring and has a plastic drip pan. Cx needs friction to stop the unit from rotating in drain pan. Unit has no error codes and functions as designed."
We serviced a
MAYTAG WASHER
Model MVWB835DW4
Near Rialto, CA 92376
Robert U.
Job Details: 03/10/2023
Found the unit had two error codes stored f5e3 and f5e2. Door was trying to latch or unlatch on arrival. I replaced the latch and removed the error codes. I ran a diagnostic test and all tested ok. Job completed. ; used 1 W10810403 (Latch) from stock
We serviced a
MAYTAG WASHER
Model MVW6230HW2
Near South El Monte, CA 91733
Juan
Job Details: 03/10/2023
"Replaced the motor capacitor, calibrated the unit. Ran diagnostics, all units ops check fine, the unit is working as designed."
We serviced a
WHIRLPOOL DRYER
Model WED4815EW
Near Kingsburg, CA 93631
Timothy
Job Details: 03/10/2023
Installed side panel console was not needed.
We serviced a
WHIRLPOOL DRYER
Model WED4950HW0
Near Riverside, CA 92503
Nick D
Job Details: 03/10/2023
"Found the drum belt had slipped out of position. Reinstalled and tested all ok. Verified idler, rollers, and motor pulley are all good."
We serviced a
WHIRLPOOL WASHER
Model WTW4815EW
Near Turlock, CA 95380
Timothy G
Job Details: 03/10/2023
Inspected unit found a hater broken. Replaced and re calibrated unit passed tests. Sprutch assembly is working. There may be an issue with gearcase. If the actuator breaks again and not spinning or stuck in agitate unit will require a gearcase. As of now job complete.
We serviced a
MAYTAG WASHER
Model MVWC565FW1
Near Santa Maria, CA 93458
George
Job Details: 03/10/2023
Installed parts tested check out ok complete no dents or dings cause by tech.
We serviced a
MAYTAG WASHER
Model MVWC565FW2
Near Los Angeles, CA 90042
Stephen
Job Details: 03/10/2023
"Replaced suspension rod kit, belt, splutch. Control is working properly at this time. No error codes found. Ran calibration, auto test cycle, drain & spin. Fills,agitates, drains,rinses, and spins properly at this time. Weak floor. Complete."
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC704FSS02
Near Castaic, CA 91384
Raymond
Job Details: 03/10/2023
"Installed control and ui combo, evap cover, ice maker fan and defrost thermistor harness with thermal fuses. Tested, unit needs to regulate to temp. Collected full via iwallet"
We serviced a
GENERAL ELECTRIC DISHWASHER
Model PDT785SYN7FS
Near Paso Robles, CA 93446
Jack
Job Details: 03/10/2023
Replaced part listed and fully tested. Also checked drain tube and is installed correctly. All checked out and working as designed. Job completed
We serviced a
KITCHENAID REFRIGERATOR
Model KRFF507HPS00
Near Riverside, CA 92503
Nick D
Job Details: 03/10/2023
Replaced the freezer LED module. Unit ok after repair parts and labor covered by s code
We serviced a
WHIRLPOOL DRYER
Model WGD5100HW3
Near Oak Park, CA 91377
Dario A
Job Details: 03/10/2023
"Customer state unit doesnt heat , no heat at all, them starts working good Tested dryer and found no mechanical issues with it at this time No error codes, cycling perfectly fine"
We serviced a
KITCHENAID DISHWASHER
Model KDFE204KPS0
Near Victorville, CA 92392
Drew M.
Job Details: 03/10/2023
Replaced parts and ran cycle. Unit passed all tests and is operating as designed.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX735SDHZ07
Near Los Angeles, CA 91344
Gabriel G
Job Details: 03/10/2023
"Removed old icemaker and thermistor harness and installed the new one, verified that the damper and Evap fans are functioning. Verified that icemaker began to cycle. Customer will advise any temperature problems continue."
We serviced a
WHIRLPOOL OVEN
Model WOS51EC7AB01
Near Apple Valley, CA 92307
Cesar
Job Details: 03/10/2023
Customer instruct on function unit was set for celsius.
We serviced a
MAYTAG WASHER
Model MVW6230HW1
Near Porterville, CA 93257
J.E.
Job Details: 03/10/2023
Cycled unit and found bad connection. I control board causing drain pump to fill. Secure connection and re-tested unit all test pass. Job complete it
We serviced a
KITCHENAID DISHWASHER
Model KDTM404KPS0
Near Bakersfield, CA 93311
Jim
Job Details: 03/10/2023
Outer trim gasket was blocking the door from closing all the way. Straighten out the gasket and unit is working without leaks. Victoria at the office is going to do the follow through of the service bench claim for property damage.
We serviced a
JENN-AIR OVEN
Model JJW3830WS02
Near Clovis, CA 93619
Doug S
Job Details: 03/10/2023
"Tested oven, unit maintained temperature on bake and convection bake, unit is working as designed.
We serviced a
KITCHENAID RANGE
Model KSGG700ESS2
Near Victorville, CA 92395
Drew M.
Job Details: 03/10/2023
Replaced parts and ran cycle. Unit passed all tests and is operating as designed.
We serviced a
FRIGIDAIRE REFRIGERATOR
Model FRFS282LAF1
Near Shafter, CA 93263
James
Job Details: 03/10/2023
Installed new fan. Cx to allow 24 hours for temps to stabilize.
We serviced a
WHIRLPOOL DRYER
Model WGD8127LW1
Near Bloomington, CA 92316
Robert U.
Job Details: 03/10/2023
After replacing all parts ordered the unit is now getting to 155 degrees on high. As for the eco settings it defaults as the option because its a energy saver but it cant be automatically turned off it has to be manually turned off each cycle. All functions tested properly after repair. Job completed.