Not leaking water and making loud noise in spin. I found gearcase seal failed and water washed drive components out. Ordering parts. Allow 120 mins. Will need to break washplate out. ; ordrng 1 W10902814 (washplate) and 1 W11449840 (Gearcase) and 1 W11481722 (Actuator)

"Unit is not spinning properly, and Gearcase sounds like it is struggling to spin. Transmission sounds like it is screeching at the beginning of start up. Will need to replace parts again. They are defective. ; ordrng 1 W11454734 (Gearcase) and 1 W11283592 (Motor) and 1 W10721967 (Cam) and 1 W10528947 (Hub) and 1 W11130362 (Suspension) and 1 W11481722 (Actuator)"

"Upon arrival according with customer unit dont dry correctly, check the unit and found lint in the vent hose causing the air restriction. Remove the restriction and retest the unit. Check temperature on the outlet and have 165F. This unit is working properly. Job complete"

Adjusted igniter closer to burner tube. Tested several times without failure

"Upon arrival found unit with door locked, check the unit and found a bad control board. This unit doesnt have any water inside, and unit keeps running the drain pump. This unit will need new control and flow switch. ; ordrng 1 W11616491 (Control board) and 1 W11044866 (Flow switch)"

Freezer door swinging open. Not staying closed. Re adjusted freezer door seal with heat. Allow for door seal to form. Components okay. Operating as designed

Cx stated that filter never came with product also unit would not go into manual diagnostics seal system ok good frost pattern across evap will order control elec; ordrng 1 W11266112 (Filter water) and 1 W11034363 (Control elec)

Interface failure will order double oven has to come out of wall parts are not in stock; ordrng 1 W11428581 (Interface stainless) and 1 W11271175 (Control elecl)

FC temp is 0.5f. Freezing food in RC. Needs data loggers.; ordrng 1 W11558182 (HV control) and 1 W11518204 (UI control)

"Found frozen FZR drain. Deiced FZR drain. Replaced FZR door gasket. FF gasket came packed wrong, damaged. Must be in tall flat box. Reorder FF gasket. Instructed customer to leave FZR door closed for 4 hours. 2 count job. Allow extra time.; ordrng 1 241786011 (Door gasket-FF)"

Upon arrival found unit with water on the detergent dispenser causing failure. Check the unit and the detergent pump is no working properly causing the failure. Replace the dispenser assembly. Retest the unit and now unit is working properly. Job complete

Old unit had compressor issues. Removed old unit and installed new unit. New unit operates as designed

New Gearcase came without agitator bolt. ; ordrng 1 WH03X34137 (Gearcase)

"All elements bad , checked resistance open.Installed 1500 watt elements working . Checked voltage good and neutral good. Ordered 2400 watt elements will return with parts.; ordrng 2 W11396790 (Element 2400 watt)s"

"Oven not turning on, has power from outlet.Control is bad, has power and neutral. Ordering control board.; ordrng 1 WFG535S0LS4 (Control board)"

"JB out 4/11/24.Verified DOP as 4/29/23Verified no cooling inFF section, very poor cooling in the FC.Compressor emitting a loud sound indicating internal failure.ORDERING COMPRESSOR AND EVAPORATOR AND REQUIRED LOKRING FITTINGS********((PLEASE ALLOW JOB COUNT OF 4 FOR COMPRESSOR AND EVAPORATOR))*****R600aSEALED SYSTEM REPAIR. ALLOW NEEDED T8 E; ordrng 1 W11488141 (EVAPORATOR) and 1 W11504419 (LOKRING (Suction Line to Evaporator)) and 1 W11504449 (LOKRING (Capillary Tube to Evaporator)) and 1 W11393974 (COMPRESSOR R600a) and 1 W11504415 (LOKRING (Suction Tube to Compressor)) and 1 W11504431 (LOKRING (Compressor to Condenser)) and 1 W11506619 (LOKRING (Charging Tube to Compressor)) and 1 W11506635 (LOKRING (Charging Tube to Schrader Valve)) and 1 R600aREFRIGERANT (50 Grams) and 1 W11109499 (DRIER (NON DYE)) and 1 W11504445 (LOKRING (Heat Loopto Condenser)) and 1 W11504449 (LOKRING (Capillary Tube to Evaporator)"

Found drive hub worn out causing basket to go off balance odering drive hub and agitator ; ordrng 1 W11550891 (Agitator) and 1 W10528947 (Drive hub)

Found bad light transformer and control odering control and transformer ; ordrng 1 W11325786 (Control) and 1 W11238401 (Transformer)

Dc circuit is dropping power ordering all fans ; ordrng 1 W11087438 (Evap motor) and 1 W11249952 (Evap motor freezer) and 1 W10846539 (Ice box fan)

Lid cracked on left side causing lit to not close properly. Ordering new lid and hinges. ; ordrng 1 W11259006 (Lid) and 1 WP8563965 (Hinge) and 1 WP8572974 (Hinge)

Unit not able to shift from agitate to spin. Ordering new shifter and pulley wheel. ; ordrng 1 WH03X30517 (Shifter) and 1 WH03X32097 (Trans pulley and nut)

Unit has bad light socket in ff section. Socket is shorted out. Quoting for new socketParts: $21.09Service Charge: $145.00FRL: F12 - $139.87 Additional Labor: $0.00Other: $0.00Subtotal: $305.96Tax: $1.58Job Rate: $307.54Collected 145.00 service in cash; ordrng 1 218906802 (Light socket)

"JB OUT 4/11/24. Customer states freezer drawer is very difficult to open and close. Additionally, upper right hand door gasket is cracked, not sealing. Ordering replacement refrigerator door gasket 10830162, Left-hand and right hand freezer drawer slide part number W11658402 quantity of two; ordrng 2 W11658402 (SLIDE)s and 1 W10830162 (GASKET FF UPPER)"

Found the refrigerator temp at round 45 degrees and the freezer at 1 degrees. I ran several diagnostic test and all functions passed but the temp in the refrigerator is not correct. Ordered main control and wire harness that comes with the new temp sensor for the refrigerator section. Will come back with the damper control. Harness is on back order so I informed the customer on the process. ; ordrng 1 W11524469 (Control electric) and 1 WPW10422363 (Harness wire)

Start switch not working. Part on order follow up required. ; ordrng 1 WP3398094 (Switch)

Unit is not cooling now Called tech line File number 7738874175 told to replace control. Ordering control not in stock.; ordrng 1 W10807590 (cntrl-elec)

"Replaced control, oven temp sensor, and oven door gasket. Tested unit. Unit operating as designed. Job complete."

"SR #- 7738870539, unit need water valve and tube. Please I need refrigeration tech as helper, unit need to be moved out to access the parts, built-in.; ordrng 1 WP2307650 (Water valve) and 1 W11662302 (Water tube)"

"Upon arrival, inspected unit unit would not start to spin in like it make a loud humming I replaced the actuator and capacitor. Retested unit after checking, splotch clutch was fine belt was fine during spinning. The motor found that the motor was seizing up I was able to free it. I started the motor in a calibration cycle to calibrate the capacitor and actuator during this spin cycle the unit completely sounded very loud like the motor is going out ordering ordering a motor gear, case assembly and drive hub; ordrng 1 W11026785 (Drive motor) and 1 W11449840 (Gear case assembly) and 1 W11551646 (Spanner nut) and 1 W11510461 (Wash plate), used 1 W11395618 (Capacitor), and 1 W10913953 (Shift actuator) from stock"

No parts in box for this job. Part are highlighted on paper. Unit will need new spark igniter. Follow scheduled for Tuesday 16 anytime.; ordrng 1 W11524031 (Ignite er)

Visual and physical inspection plus functional testing and found a bad clock board. ; ordrng 1 W11620552 (Clock board)

Unit is not draining at all. F21 shows up. Talked to parts and will get it on truck. 280187 pump assembly. ; ordrng 1 280187 (Pump assembly)

Robert with tech line. Ran test 81 and 82. Still no water to unit. File number for this call. Steam out fill tub freezing and see if it works after this. 87173791. ; schdld next appmnt for 4/15 MON !

"Received another defective control. This time, the main valves and drain pump are working fine. But 3 secondary valves and the UI are not functioning properly. The UI is blinking and unusable. I plugged the old control back in to see if the UI has failed, but it works fine with the old control. I need to order a third control now. Cx doesnt want to wait for another part and is going to Costco to ask for a replacement.; ordrng 1 WH22X36637 (Control)"

Broken strike. Part on order follow up required. ; ordrng 1 W11457841 (Strike)

Found broken strike.; ordrng 1 W11457841 (Strike)

"Tested unit found defective timer, thermostas, and igniter ; ordrng 1 WE04X24550 (Timer) and 1 WE04X25195 (Thermostat) and 1 WE04X26138 (Thermostat) and 1 WE04X25199 (Thermostat) and 1 WE04X25201 (Thermostat) and 1 WE4M449 (Igniter)"

"JB out 4/11/24.Customer states washer lid will lock but washer does not start.Found failed Capacitor.Installed replacement Capacitor W11395618 (USED FROM TRUCK STOCK). Tested operation. Observed loud grinding noise from splutch.Installed replacement (Cam/Splutch ASM from Truck Stock.)Reassembled unit.Unable to run calibration cycle, unit will not enter but only spins at high speed.Spoke with Austin at Whirlpool factory Tech line. After several attempts to run calibration cycle, Austin recommended replacing the machine control. Ordering machine control, and HMI under the manufactures warranty at no charge to the customer.; ordrng 1 W11675701 (HMI) and 1 W11627413 (MACHINE CONTROL), used 1 W11395618 ( CAPACITOR), and 1 W10721967 ( CAM KIT) from stock"

Pulled up to house and found that harnesses terminal block was broken and connectors looked bent and frayed. Showed customer because he pulled up to house same time as me. Ordering new harness. ; ordrng 1 W11529071 (Harness)

Unwrapped front panel with customer who left in film and found a scratch on bottom right of front panel. Will need new panel sent to customer. Will order and install on return.; ordrng 1 WD27X33580 (White door panel)

Door falls down. Ordering hinges. ; ordrng 1 W11712995 (Left hinge) and 1 W11712996 (Right hinge)

Gasket broke. And ice door frozen shut. Keeps freezing shut ordering door. ; ordrng 1 W10917313 (Gasket) and 1 W11594927 (Ice door)

F3e2 error code. Light stays onOrdering parts. ; ordrng 1 W11618921 (Acu) and 1 W11459149 (Hanrness) and 1 WPW10298258 (Harnes) and 2 WP3387223 (Electrode)s

Compressor was seized up. No cool ordered new compressor. Schedule as training for TR.; saved tckt

Unit not seeing lid lock; ordrng 1 W11513248 (Lock) and 1 W11626074 (ACU)

DSI module not receiving 120 volts from board; ordrng 1 W11620680 (ACU)

Found diffuser exexively loud and clicking need diffuser.; ordrng 1 W11164593 (Diffuser)

Found faulty damper

Broken wire harness in the door; ordrng 1 LW11202405 (Door)

Fresh food evaporator is frozen up badly ; ordrng 1 W11087438 (Harness)

Damper leaking ; ordrng 1 WP67006341 (Gasket) and 1 WPW10196393 (Damper)

Found no voltage to valves; ordrng 1 WH22X35518 (Control board) and 1 WH08X29513 (Harness)

Cx claims that washer is filling then draining water out of drum before agitating.ordered new control board.; ordrng 1 W11608056 (Control board)

Installed parts tested to a fill drain tested ok complete.; ordrng 1 WD19X25461 (Drainpump)

Found refrigeratorbuilding condensation in freshfood area found dead deli Ui customer decline estimate at this time do not order parts complete paid for service .; ordrng 1 KRMF706ESS (Door) and 1 WPW10769076 (Ui) and 1 W11170612 (Harness)

Found refrigerator ice maker not filling ice maker on advance no fill ; ordrng 1 WR57X30890 (Isolationvalve) and 1 WR30X39385 (Icemaker)

Found bad fresh food door gasket ordering new; ordrng 1 W11240749 (Door gasket black)

Found both mounting nuts were broken ordering new; ordrng 2 WB01X10124 (Nut assembly)s

"Customer states the unit is not freezing properly. Some of the food is not frozen solid and ice cream becomes mushy after only a day or two. Called WPTS(7738871236) and spoke to them about what I saw. The evaporator fan was not running while I was speaking to the customer. I turned down the cooling and closed the door. As she was removing the Fc items the fan came on. When I opened the evaporator compartment there was only a partial frost pattern. Later after troubleshooting it looked better even though I would expect it to be worse since I had the unit open and the evaporation panel off while I was inspecting for leaks. When doing a wattage test there was only about 15-20 watts. Per WPTS it should be more like 70-90 watts the amp draw was about 1 amp. I looked for evidence of leaks in the unit and evaporator compartments but found no evidence. WPTS recommended pressurizing the unit with nitrogen and checking for leaks. If I do this now the customer will not have any cooling at all until I can get sealed system parts to repair this unit. See notes on scheduling.; ordrng 1 W11582579 (Compressor) and 1 W11504415 (5/4 NR MS 00 (HEAT LOOP TO CONDENSER)',) and 1 W11504449 (4/2 NR AL 00 (CAPILLARY TUBE TO EVAPORATOR) and 1 W11109499 (DRIER (SERVICE DRIER WITHOUT DYE) (ALSO ORDER THE FOLLOWING LOKRING PARTS)) and 1 W11504415 (8.5/8 NR MS 00 (SUCTION TUBE TO COMPRESSOR) and 1 W11504431 (7/5 NR MS 00 (COMPRESSOR TO CONDENSER)',) and 1 W11506635 (TUBE, CHARGING (1/4' W/ SCHRADER VALVE)',) and 1 W11506619 (8 NK MS 00 (CHARGING TUBE TO COMPRESSOR)',)"

"Rotor screw strip broke can not take out. Customer has waited to long for repair wants new appointment soon, or replaced unit.; ordrng 1 W1144984 (Gear case) and 1 W1075448 (Clutch) and 1 W10734521 (Slider) and 1 W11260238 (Rotor) and 1 W11510461 (Wash plate)"

Rails ar not closing correctly and looking up right part. ; schdld next appmnt for 4/12 FRI !

Found unit has a tear on the right gasket were mulligan is sweating and dripping water down to freezer door. Gasket W10830162. ; ordrng 1 W10830162 (Gasket gray)

"Drain pump wire broken, repaired drain pump wire.Ran diagnostic cycle test, all test passed. Job complete."

"Found igniter failing to light flame, reinstalled igniter, unit is operating as designed"

"Found agitator screw came loose not allowing agitator to stay tight and function properly. Fastened down screw. Tested unit, all ops now working as designed."

"Removed and replaced motor, blower wheel and repair kit. Customer stated today that the door seal is missing. Ordering door seal. ; ordrng 1 WPW10354795 (seal-door)"

Cycled unit and found bad suspension causing damage to tub and wash plate ordering parts for repair ; ordrng 1 W10902814 (Wash plate) and 1 W10752719 (Tube) and 1 W11130362 (Suspension)

"Customer concerns; washer makes grinding noise, basket vibrates excessively (weak suspension). Gearcase leaking (loud). NEED AUTHO FOR ALL THE PARTS IN THE LIST. WASHPLATE AND LATCH WILL ONLY BE USED IF NEEDED. 2 JOOOB COUNT (1 HR DRIVE TIME); ordrng 1 W11396716 (Suspension) and 1 W10902814 (Washplate) and 1 W11449840 (Gearcase) and 1 W10721967 (CAM) and 1 W11239857 (Belt) and 1 W11700916 (LATCH)"

Cleared obstruction in drain line. Unit is functioning normal.

"Freezer ice maker is not making ice. Customer states, that an Electrolux technician was there to inspect the ice maker, but he never followed up. Techline rep requested PICS from behind the freezer to deem unit unrepairable. I CALLED TECHLINE TO OBTAIN SR#. RECORDING: NO ANSWER DUE TO HIGH VOLUME OF CALLS. I WILL CALL FRIDAY.; schdld next appmnt for 4/12 FRI !"

Long dry times and loud during use. Found bad pulley. Removed and replaced pulley and coil valves. Tested now working as designed cx instruct on getting vent cleaned out

Inspected unit and found breaker power short. Reset and unit fired up. Unit is now working per design. Cx approved repair.

Found the strike on the lid broken so the unit is unable to preform a cycle. I replaced the defective strike and all functions were restored. All functions tested properly in diagnostics. Job completed.

Tech was assigned as a helper;

Found loose belt on motor. Replaced belt from truck stock. Tested unit unit functions as normal. ; used 1 W10006384 (Belt) from stock

Door switch broken. Replaced with pre id part. Job complete.

Ran diagnostics and found an F9E1 error code. Replaced drain pump and ran cycle. Unit passed all tests and is now operating as designed.

Found failing control board; ordrng 1 WD21X33685 (Control board)

Slider rattling during agitation suspect clutch and slider ; ordrng 1 W10754448 (Clutch)

F86x18. Water supply issue. Valve was working and filling fine. Found issue with pressure sensor. It had a bunch of debris inside which was causing it to misread the water level. It looked like plastic wrap from shipping. I cleared it and retested. Unit is now functioning normally.

No answer at the door. Office called CX. Told CX im at the home.Answered. NEED MORE PARTS THE EVAP COVER IS IN ICE AND WILL BREAK. ON ORDER. ; ordrng 1 5304519654 (Evap cover)

Wash motor would not turn on during cycle. Ordering new pump.; ordrng 1 5304519906 (Wash Motor)

Ran unit to another breaker and unit running with no problems. Confirmed it is a bad breaker. All ops with machine testing out normal.

"Timer not advancing, replaced timer and tested unit working properly"

Inspected unit and found unit with 2 minutes left n a cycle. Unit is working per design. The lid does have a crack and is preventing lid from closing all the time. Cx is insisting that the unit doesnt work. Every time Ive been here the Cx is trying to get me to help her buy a new by saying its not fixable. Cx needs a Spanish speaking technician. Im calling office to call her. Im here replacing the broken lid. After I repair I will run my tests on the unit. If I find anything more wrong I will address those issues then. If I run my tests and have no issues then the repair is complete. Also she is making complaints as I type this. ; ordrng 1 W11259006 (Lod)

"Not filling with water, repaired harness to valve tested unit working properly. Loose connection had to move unit"

Found vent tube not connected to back of dryer. Advise customer to contact Ventura TV. This was an install issue.

Need more parts. Job not done. ; ordrng 1 WP697772 (Blower) and 1 W11364931 (Motor)

JB out 4/11/24.Installed replacement ice container. Verified no ice production.Inspected condenser coils found clean but room temperature (not hot).******ALLOW TIME JOB COUNT 3 ON RETURN VISIT FOR COMPRESSOR REPLACEMENT*****; ordrng 1 W11654344 (COMPRESSOR 134a) and 1 WPW10143759 (DRIER UV) and 1 WPW10626970 (TUBE) and 1 876764 (VALVE) and 1 WP978025 (VALVE) and 1 W11492867 (EVAPORATOR)

Installed freezer door gasket product tested ok complete

"Unit found drying a load and working properly, ran diagnostic for codes,FAE2 vent wax electrical problem, F9E1 draining issue and F8E4 overfill, float switch open.,ordering parts,W11545764 Float switch,W11416362 Pump&Motor.; ordrng 1 W11545764 (Flat switch.) and 1 W11416362 (Pump&Motor)"

"DW making a loud humming noise at wash cycle, F10E2 error code which indicates the wash motor is bad, order W11416362 Sump Pump Motor.; ordrng 1 W11416362 (Sump pump motor.)"

"Found screw stuck in cooling fan removed all tested good."

"Found a bad slider. Had it replaced. Also, drain hose was kicked. Had it repaired"

Found the unit has a f7e1 error code. Found the motor open on the windings. I replaced the sump and motor assembly and ran a diagnostic tested. The drain pump was louder the pan normally on initial power up but thats because it was running dry. After running water and doing a diagnostic cycle all functions worked and sounded normally. All functions now ok and I removed the error codes stored. Job completed.

"Found base plate out of place causing freezer door to hit plate before its fully closed, realigned base plate and now freezer door closes properly"

"Checked the unit the washer has bad main board and pressure switch , est to replace both $803.76 Mr declined to repair the unit at this time collected 145.00 trip charge paid by card ; ordrng 1 W11031829 (cntrl-elec) and 1 WPW10448876 (switch-wl)"

Found a broken latch assembly. Had it replaced

"Checked the unit the dampener asm is rattling when it opens and closes , ordered parts ; ordrng 1 W10479155 (control)"

"Inspected unit, unit would not shift. Replaced cam actuator and belt. Unit then passed all tests. Job complete"