Installed new heating element. All functions tested okay. Unit is heating as designed. Call complete.

Lid was broken. Removed and replaced lid and tested unit. Unit functions normal now.

Removed and replaced Eva cover an air tower. Unit functions normal now

"Unit had bad water valve, replaced and tested unit , working as designed"

"Unit had deformed freezer door gasket, used steamer to soften"

Replaced parts and ran cycle. Unit passed all tests and is operating as designed.

Replaced oven console. Operation tested as designed.

"Locked rotor. Replaced compressor, pressure tested, checked ok. Pulled vacuum, recharged 50g r600a. Refrigerator operating as designed at time of service."

Replaced harness. Tested unit. Unit operating as designed. Job complete.

Pulley was removed and replaced. Unit is working as intended. Job completed.

"Upon arrival found unit with error codes F7E7, F6E3, F7E4 and F7E3, this about motor problem and clutch. Check the unit on test mode and the unit doesnt agitate or spin. Check the unit and found the harness is back and additional the control board as well. Replace this two components on the unit. Retest the unit and unit is working properly. Job complete."

"Upon arrival found unit no working properly on the door switch, check the and found the primary switch is bad, this because is no continuity on the normal close, causing the failure of the error message on the screen for the door. Install the new interlock assembly, retest the unit and now unit is working properly. Job complete"

Install the new harness control board and thermistor on the unit. Retest the unit and now unit is working properly. Job complete.

"Removed and replaced door, tested ops unit working ok. Customer will monitor ice production."

"Found unit within model and serial number for led module replacement. Removed and replaced all led modules, unit now checking ok"

"Found metered wheels on bottom rack, removed and replaced rack unit now working properly."

"Checked unit found latch connector not fully inserted into control, re inserted and unit checked ok."

"Uninstalled unit, removed and replaced fill valve, harness,and inlet water flow meter. Asked customer to monitor and report any issues"

Replaced failed pressure switch product tested ok failure code clear complete

Installed new drive motor belt actuator and cam kit product tested ok complete

Replaced element that was grounded to box replaced thermostat cut off and high limit came with thermo cut off sending other high limit back product tested ok complete

Installed oven probe and bake igniter product tested ok

Installed new water valve product tested ok complete

"Moved and replaced units, rollers belt and rest of drive kit. Also secured loose blower wheel facia plate. Ran unit for five minutes. No noise customer approves function."

Installed components test pass. No leaks door seals properly. DONE

"5.5z 134ARemoved charge from sealed system. Removed pre-cooler and filter drier. Installed pre cooler, filter drier and access stub. Vacc and charged the fridge to recommended level. Unit is holding charge. ALLOW 24 hrs for unit to settle temps. DONE."

"Removed power rom washer, replaced suspension cam and belt. Assembled unit, restored power. Ran and passed calibration cycle. DONE."

Found harness was bad. Replaced and checked out. Checked all functions and unit is working. Job completed

Unit is not lock. F5e3 lock failure. Found and replaced lock mechanism and tested unit and made sure lock is functioning correctly. Passed test. Job completed

Replaced parts listed. There was a hair line crack on blower wouldnt come off. Replaced and tested. unit is now working properly and as designed. Job completed

Installed new control board and dryer worked OK

Installed the new doors boot. Washer ok

Installed the new couch assembly now door closest properly

Install evaporator cover panel on fridge worked OK

Replaced front right burner base. While testing oven gfi on counter blew. Advised customer that unit must be on dedicated circuit.

Installed ice maker and jumped connection t and h. Unit working at this time

Unit latch broken and will not lock. Installed new lock and unit is working as intended.

Installed new parts and retested unit now working as designed job completed

Removed wall oven and Installed new ui and retested unit now working as designed job completed

"Installed dryer, slides and unit is quiet now."

Fixed defective drain pump. Tested unit and is working properly.

"Found effective drum kinked to back of unit, fixed defective drum, tested unit and is working properly."

"Tested unit and is working properly. Checked shut off valve. Checked dryer, gas valve and checked connection to dryer gas valve. No leaks found at this time."

Tested unit found deffective float switch, fixed defective float switch tested unit and is working properly

"JB Out 12/14/23.Customer states with the dryer has little heat and takes several hours to dry clothing.Upon arrival found newly installed dryer in laundry room connected with thin foil type ducting material going inside wall above kitchen to the exit of the house. Tested dryer with wet clothing. Found unit is heating but short cycling. Burner flame says on between 23: 45 and then cycles off. Remove the dryer from away from the wall and then remove ducting from dryer. Tested dryer again in timed dry cycle. Verified burner does not any longer short cycle. Counted 11 1/2 minute on interrupted burner duration with wet clothing and dryer. Advise customer no mechanical issue with dryer itself but ducting system inside wall to the exit of the house is partially restricted causing short cycle burner operation lead to very long dry time. Recommend customer replace existing thin foil, tight ducting material with rigid metal ducting material to prevent potential hazard of fire or loss of life. Also recommend customer have duct inside wall, professionally cleaned to remove any and all restrictions. No charge to customer. Job complete."

JB out 12/14/23.Installed replacement TOP WH10X33077.Reassembled unit and tested operation with customer.Unit now operates as designed. No Charge To Customer JOB COMPLETE

"Replaced light modules working as per designed, customer approved. Job complete."

Installed suspension rods and tested unit. Unit is working properly. Customer approves function at this time.

Removed and replaced console. Tested unit. All tests good.

"Unit has a bad capacitor, replaced cap, tested and washer runs properly.Job completed."

"Found door latch broken, replaced, tested and unit runs properly. Job completed."

"Unit has rollers making noise.Replace dryer kit, tested unit,runs good as designed, job completed."

"Unit not responding, found defective door latch, replaced latch, tested and run washer now working as designed.Job completed."

"Unit was found leaking, clogged with liquid soap under dispenser,door lock was not working, replaced door lock, tested and run unit which is now working to specs. Job completed."

"Diffuser stuck and making noise, Replaced diffuser , unit running to specs.Job completed"

Customer states that unit is not draining After running diagnostic test find that air gap is clogged Unclogged air gap Tested unit working properly as required

Replaced all selected parts Unit working properly as required

Replaced moisture sensor from my stock Tested unit working properly as required

Customer states that unit is not working properly After running diagnostic test find that unit has a bad sump motor Replaced all selected parts Unit working properly as required

Replaced latch tested door is closing properly Job complete

Fan motor making loud noise replaced motor fan is on and running loud noise is gone. Job complete

Installed new ice maker and inlet valve. All functions tested okay. Unit working as designed. Call complete

"Installed new door assembly, all functions tested okay. Unit working as designed after part installed. Call complete."

Installed new heater assembly. All functions tested okay. Unit working as designed. Call complete

Because of physical damage a new fresh food section right door seal has been replaced

Remove existing control/sensor. Installed new control/sensor. Test ran unit. Unit operating as designed.

Removed Evap cover. Defrosted ice build up. Cleared drain. Installed Evap cover now working as designed.

"Installed rc door, used silicone to seal unit. Unit functions as designed."

"Drain hose not inserted all the way, slipped out causing splashing in plumbing box, shaking came from load shifting during spin. Calibrated unit, unit functions as designed."

Upon arrival inspected unit found a actuator was bad replaced actuator and capacitor re-tested unit in diagnostics unit passed all diagnostic test put the unit into drain and spin. The unit went into drain and spin just fine. Also did a quick wash cycle unit pass all tests on the quick wash cycle advise consumer to never overload the unit or two. Make sure that all loads are balanced and it is now working as intended. Job complete

Upon arrival inspected unit found that the unit had a faulty drain pump replaced drain pump tested unit in diagnostics unit passed all diagnostic test and is working as intended. Job complete

"Upon arrival, inspected unit, found that ceramic arm had fallen off that holds the heating element to the top of the microwave cavity. Replaced it with a new one that comes in a kit tested unit unit is working as intended. Job complete"

"Upon arrival, replaced outer tub, inner tub transmission, cam drive belt and drive hub tested and wash plate unit unit is working as intended job complete"

After replacing both knob and timer the unit is now able to select a cycle and continue with the cycle. All functions are now working properly. Job completed.

Found the cold water valve not closing all the way. So it is allowing a constant trickle of water into the unit. I replaced the valve and checked for dripping going into the unit and no more dripping occurring. All other functions tested ok. Job completed. ; used 1 W11513255 (Valve) from stock

After replacing the door seal the door is now sealing properly on all side. Door now closes better. Job completed.

After replacing the stuck valve all functions of the cooktop are now restored. All functions pass. Job completed.

Replaced listed parts in order to fix cracked out tub issue had to replace Gearcase in order to make sure new seal was installed. Tested after repair all ok.

Replaced faulty oven appliance manager in order to fix f1e1 error message when trying to use oven. Tested after repair all ok.

"Replaced center burner, flame now is normal. All flames look normal now. Clock now showing the right time after connecting unit to Wi-Fi. Unit ok after repair."

"Replaced all led lights, now all lights are working. Unit ok after repair."

Replaced all led lights per service pointer. All lights now work. Unit ok after repair.

Replaced bad grinding sound motor and defective shifter

"Replaced tub, unit test ok. Complete"

"Replaced drain hose,motor and sump assembly,and drain pump.dishwasher working properly."

Dw had defective drain pump and motor.replaced motor and sump assembly. dw working properly.

Dishes in dishwasher dry on arrival. Ran diagnostic and had no indication of unit being defective.dishwasher is working properly.

Replaced infinite switch. cooktop working properly.

"Replaced all 4 shocks. Ran test # 12 and drain & spin. Locks/unlocks, fills, washes, drains, and spins properly at this time. Complete."

Replaced capacitor shifter and spritz. Unit passed all test and is working per design. Job complete.

Replaced all 12 led lights. Unit lighting per design.

Replaced failed thermal fuse. Unit working per design. Job complete

Customer stated that the timer knob broke off the timer. Found shaft for timer broke. Removed and replaced timer and knob. Parts and labor covered under s code. Tested all works good at this time.

Per Special Project #: S84638 removed and replaced all led modules with kit number W11632139. Tested all works good at this time.; used 4 W11632139 (Led module) from stock

Customer stated that the unit is making noise in the wash cycle. Ran unit through diagnostics and found gear case is clicking. Rotor bolt is stripped removed and replaced gear case rotor stator clutch slider and bolts tested all works good at this time.

"Removed unit from cabinet, adjusted fan shroud in microwave & microwave cover, ran microwave heating water heating test, unit operating as designed."

"Found sprung lid, it closing even, Replaced lib assy, ran self diagnostic cycle, unit operating as designed."

"F7E4, Checked the unit the washer had a bad slider , replaced slider with truck stock one , tested operations ok now at this time ; used 1 W10734521 (SLIDER) from stock"

"Found the unit's compressor not working properly, replaced, cntrl-elec and inverter-box, check compressor,condenser and evaporator fan motors, unit start work"

F1E2 and F3E3 present. Replaced control. The last control installed was defective. Recalibrated and ran diagnostic cycle. Faults did not return.