Found a belt slipped off. Secured belt and tested unit. Unit functions normal now.

Unplugged unit and let sit for five minutes. Plugged it back in. Set clock and ran. Bake cycle to 350. Unit functions normal now.

Removed and replaced baffle and tested unit. Unit functions normal now.

"Found fabric softener water line loose and leaking when using, fixed water line and tested unit, working as designed"

"Installed new panel control cover and tested unit, working as designed"

"Installed new drain pump and tested unit, working as designed"

"Unit had bad blower motor to ice maker, replaced and tested unit, working as designed"

"Installed new appliance control and tested unit, working as designed"

"Found loose harness on water valve, fixed harness and tested unit , working as designed"

Replaced radiant sensor and Thermal-fix. Dryer heating at time of service.

Installed sprayer arm. Unit operating as designed. Job complete.

Replaced control board. Tested unit. Unit operating as designed. job complete.

Replace gear case. Tested unit. Unit operating as designed. Job complete.

Burner caps were swapped and in wrong location. Installed caps correctly. Unit operating as designed. Job complete

Drain pump shorted out. Drain pump and valve were removed and replaced. Unit is working as intended. Job completed. ; used 1 W11165546 (Valve) from stock

Install the new motor and belt on the unit. Retest the unit on a spin maximum speed and now unit is working properly. Job complete.

"Found the unit not cooling properly, replace ui control, cntrl-elec, harness wire, control and motor evaporator, unit start work"

"Found the unit not cooling properly, replaced led module kit , cntrl- elec, check compressor condenser and evaporator fans motors unit work properly."

Installed new control and thermistor. Re-tested heater and was able to get it to turn on with new control. I defrosted the entire evaporator. Everything should be working as designed.

F9E2. Installed pump assembly. Unit is now passing all tests.

"Found latch was tripped back keeping door from closing, reset latch all tested good"

Replaced nut and switches all tested good

Replaced slider tested good

Installed new control. All ops now working as designed.

Found oven temp needed to be calibrated. Programmed main control. All functions now working as designed and reaching desired temp with no issues.

Installed new acu and valve. All ops now working as designed.

Installed New UI and programmed. All functions now working as designed.

Loose connector to hi limit thermostat. Reconnected and secured. Unit now heating with no issues. All functions now working as designed.

Installed new switch. Tested unit and all functions are now checking normal.

Fixed- installed new part (cntrl elec) calibration test pass- auto test pass- no leaks- no errors- customer ok repair

Fixed- installed new part (console) auto test pass- unit is heating good as well- customer ok repair

Fixed- installed new part (handle) freezer door is now opening/closing as designed- customer ok repair

Fixed- found error code f9e1 pump failure- removed bad one and then installed new one (pump) calibration test pass- auto test pass- no leaks- no errors- customer ok repair

"Fixed- used part from SP (w10841140 adhesive) found gaskets to both doors to be detaching from channel, i then add adhesive into channel and pop gaskets back into channel, allow 30-40 minutes to dry- customer ok repair ; used 1 W10841140 (Adhesive) from stock"

Fixed- found lid strike to be broken causing unit not to start- removed broken one and then installed new one (strike) calibration test pass- auto test pass- no leaks- no errors- customer ok repair

Removed and replaced control board and water valve and tested unit. Unit functions normal now.

Defrosted unit removed and replaced drip pan evaporator cover and fan and harness. Defrosted unit. Unit functions no normal now

"Installed new control board and tested unit, working as designed"

"Found sump pump loose, tightened up and tested, working as designed"

"Installed new suspension rods and tested, working as designed"

"Installed new dispenser module and tested unit, working as designed"

"Customer states, that after a power outage. The washer stopped working (humming noise). Faulty capacitor. Replaced capacitor (second time). Performed calibration. Washer operating as designed. No leaks."

Replaced the parts in list. Range operating as designed.

Replaced drive motor and blower wheel. Dryer operating as designed.

Defrost and replaced evaporator cover. All functions tested normal at time of service. No leaks.

"To remove washplate, I had to break it off from gearcase shaft. Replaced gearcase, washplate and slider assembly. Washer operating as designed. No leaks.; used 1 W10734521 ( Slider) from stock"

"Customer concerns; refrigerator dispenser and UI LEDS not responding. I removed UI, disconnect/connect wire harness. Re-installed UI. All functions tested as designed."

Ui failed. Stuck key error code present. Replaced Ui. Tested unit. Unit operating as designed. Job complete.

Suspension worn out. Replaced suspension. Tested unit. Unit operating as designed. Job complete.

Control assembly broken with f2 e1 Error. replace ACU. Retested it and it passed all tests.

Speed sensor wire harness was not making contact. Wires harness was safely repaired and reattach to wire harness. Unit passed all test. Job completed.

Install the new front burners on the unit. Retest the unit and now unit is working properly. Job complete

"Install the new pump assembly on the unit. Retest the unit and now unit is working properly, no leaks found at this time."

Found rotor screw missing replaced slide kit with new screw and placed dispenser product tested ok complete

Found screw to rotor lose replaced with new screw and added lock tight product tested ok complete

"Installed heating element. Assembled unit, restored power. Ran dryer for function test passed. All ops normal. DONE."

"The dryer has a bad door switch. Removed power, replaced the switch. Restored power and tested, passed. Done."

Found the roller on the left side is making noise. Installed dryer repair kit. All sounds and ops normal. DONE.

"Replaced outer tub, slider and screws. Finished assembly, restored power. Ran test cycle, passed. All functions normal. DONE."

"Bad door latch lock assembly, I installed and secured new lid lock assembly, tested and unit is now locking and draining spinning as designed, customer approved repairs"

"Unit was calibrated 20+ when I got there, I reset the calibration to 0 , unit is now heating properly as designed, customer approved instructions on how to calibrate the units temperature, customer approved service"

Cycled unit and found agitator came off due to lose screw. Add water valve its stuck open. Installed the water valve and secured agitator back onto position and retested unit unit not working as designed job completed.; used 1 W11210463 (Water valve) from stock

Installed new parts and retested unit now cooling as designed job completed.

JB out 1/11/24 Installed replacement motor. Reassembled unit and tested operation No charge to customer JOB COMPLETE

"Customer states during FILL portion of Normal wash cycle, unit shuts off. Ran diagonal and extracted stored Error Codes : F0E3 OVERLOAD. Fall is displayed when main control, detects a washload that exceeds the capacity of the machine. F1E2 Motor Drive Module Over Voltage. Cleared codes. Tested lid lock, Fill Cold, Fill HotAgitation and Spin functions. All operated as designed but verified rubbing noise during Agitation.Removed Motor a rotor and inspected Sider assembly for proper operation. Verify operates properly. Reinstalled Motor Rotor. Further inspection found several coins and 1 button lodged between wash tub and washplate.Removed all. Tested agitation again and verified rubbing noise is gone. Tested in NORMAL wash cycle and verified correct fill, agitation, drain and spin functions.Advised customer to customer to make sure pocket are empty before washing.Advised customer to to use ONLY HE DETERGENT and no more than ONE MEASURED TEASPOON MAXIMUM. ADVISED AGAINST USE OF HE TURBO OR PODS as the concentration is too strong for the low fill, high efficiency washer.No parts used. No charge to customer.JOB COMPLETE"

Removed and replaced orifices. All tests good.

"Removed and replaced gearcase, cam, belt and actuator. Tested unit. All tests good."

Unit not agitating only spinning. I found failed actuator not engaging agitation cycle. Removed and replaced actuator. Tested unit. All tests good.

Unit making noise during agitation. I found loose pulley causing noise. Tightened pulley and tested through diagnostic. All tests good.

Replaced all selected parts Unit working properly as required

Replaced all selected parts Unit working properly as required

Replaced all selected parts Unit working properly as required

Replaced all selected parts Unit working properly as required

Replaced bad ice box fan Tested unit fan is spinning with no loud noise Job complete

Found drain line from fresh food evaporator was clogged not allowing water to drain and leak into fresh food section, cleaned out clog, tested, unit is now draining. job complete

"Because of an issue with all buttons on U I pane, a new U I panel has been replaced."

"Because of a broken door strike issue, a new door assembly was replaced."

"Visual and physical inspection leaded me to a miss aligned condensers fan blade, I have corrected the issue by making adjustments to fans motor brackets and main cabinet as well."

"Replaced turntable ring, and unit is working properly. Job complete"

Customer issue icemaker tray broken. Removed existing icemaker tray. Installed new icemaker tray. Unit operating as designed.

Dryer belt change out. Removed existing dryer belt. Installed new dryer belt. Test ran unit. Unit operating as designed.

Top lid washer replacement removed existing machine lid/latch harness. Installed new parts listed. Test ran unit. Unit operating as designed.

Removed and replaced belt and cam. Tested now working as designed.

Removed and replaced agitator bolt cam auger couple and retainer. Installed. Tested now working as designed

"Installed fc cover with thermistor, damper, seals and thermistors. Tested, unit functioning as designed."

"Doors not sealing. Heated and reformed seals, no more air leaks found"

"Upon arrival replaced washer, tub gasket, lower door, seal corrosion sensor. Also replaced vent gasket. Unit is no longer leaking. Job complete."

Upon arrival inspected unit found that unit would not unlock. Tested lid latch lid latch was not working replace lid latch tested unit unit passed all test job complete

"Upon arrival, replaced stater, rotor and clutch assembly. Also replaced main control board and lid latch but unit through a calibration cycle and a diagnostic cycled unit passed all tests and is working as intended. Job complete"

Upon arrival replaced main control board. I also repaired another wire on the harness that goes to the drain pump unit through a diagnostic cycled unit passed all test and then calibrated unit. Ran a short cycle, unit is now working as intended.

After replacing the suspension rods on the unit all functions tested ok. Job completed. Unit is no longer shaking. Job completed

After replacing faulty timer and knob the unit now operates as designed. All functions tested ok. Job completed.

Found the bushings for the suspension rods not in place. I reinstalled bushings and made sure the unit was leveled. After doing so I ran a recalibration on the control and verified operation. All tested ok. Job completed.

After replacing all spray arms the units now sending the water properly. No f codes stored at this time. All functions tested properly and no updates required for this model. Job completed.

Found stater bolt loose and slider ring loose fixed errors retested unit, unit working properly

Replaced loose belt in order to fix loud screeching noise when unit starts to spin. Tested after repair all ok.; used 1 W11239857 (Belt) from stock

Removed a lot of items from the drain pump filter they were preventing unit from draining. Tested after repair all ok.

"Replaced both thermostats,flame detector, and gas coils, in order to fix not heating issue. Tested after repair, all ok."

"Replaced faulty sparker board in order to fix oven not heating issue, tested after repair all ok. Adjusted the front right burner switch in order to fix front right burner not soaking issue. Tested after repair all ok."

"Replaced refrigerator side of the gasket due to discoloration, unit test ok. Complete"